Alarms Alarm output terminals are located at the manual rear terminal panel.
It does not change the user PID constants, but temporarily modifies the internal controller response to suppress overshoot.
Full-screen viewing: Modern portable devices provide fast and mobile access to information, but they have relatively small screens, so viewing the Honeywell UDC3300 manual may not be very user convenient.
24149 Figure 2Operator Interface Operator Interface (Figure 2) IndicatorsProvide alarm, control mode, and temperature unit indication.A 21-segment bargraph displays deviation to 10 of span and an On-Control indicator.A new and innovative Maintenance Diagnostic tool available with, expanded UDC3300 controllers is, healthWatch, a low-cost software program that puts maintenance and diagnostic data at your manual fingertips so you can monitor vital performance activities to improve your process, predict equipment failure, and minimize downtime.The UDC 3300 is totally compatible with existing UDC 3000 applications and installations.Page 32 Honeywell UDC3300 Manual Page 32 Configuration 24 UDC3300 Basic Model: DC330B User Manual 5/00.4 SP Ramp, SP Rate, or SP Programming manual Set Up Group Table 3-3 SP Ramp Function Prompts Function Prompt Lower Display Function Name Selecti.Page 16 Honeywell UDC3300 Manual, page 16 Installation 8 UDC3300 Basic Model: DC330B User Manual 5/00 Input#1/Input #2 The 250 load resistor for 4-20 mA or the voltage divider manual for 0-10 volts or the 500 ohm C/J compensation resistor.There is also indication of when Remote Setpoint is active, the status of the control relays, and whether a setpoint program is in Run or Hold mode.Industrial Automation and Control Honeywell Inc.Page 45 Honeywell UDC3300 Manual Page 45 Configuration 5/00 UDC3300 Basic Model: DC330B User Manual 37 Function Prompt Lower Display Function Name Selections or Range of Setting Upper Display Factory Setting A1S2 EV SP Programming EventAlarm State.Limit ControlProvides a latching relay which is activated whenever the PV goes above or below a preset setpoint value.Page 14 Honeywell UDC3300 Manual, page 14 Installation 6 UDC3300 Basic Model: DC330B User Manual 5/00 Composite Wiring L1 L2/N Auxiliary Output Terminals See Figure 2-13 manual Outputs and Alarms Terminals Time Proportional.Page 75 Honeywell UDC3300 Manual Page 75 Configuration Record Sheet 5/00 UDC3300 Basic Model: DC330B User Manual.
Page 67 Honeywell UDC3300 star Manual cracked Page 67 Setpoint Rate/Ramp/Soak Program Operation 5/00 UDC3300 device Basic Model: DC330B User Manual 59 Program Record Sheet Draw your ramp/soak profile on the manual record sheet shown in Figure 5-2 and fill in theassociated info.
Page 22 steam Honeywell UDC3300 Manual, page 22 Installation 14 UDC3300 Basic Model: DC330B User Manual 5/00 Auxiliary Output 16 17 Auxiliary Load Connect shield to ground at one end.
Simple keystrokes let you set operating parameters that meet your process manual game control needs.
Quality/SupportThe UDC 3300 is covered by a 2-year warranty and backed up by a toll-free phone number for technical assistance.In the.S.A.: Honeywell Industrial Automation and Control, 16404 North Black Canyon Hwy., Phoenix, AZ 85023, (800) In Europe: Honeywell.A., 80084 Amiens Cedex 2, (33) Honeywell Control System Ltd., Honeywell House, Bracknell, UK-RG 12 1 EB, (44) In Japan: Yamatake-Honeywell.Mains power input and relay contact outputs:.5 kV, Common Mode and Differential Mode.Page 54 Honeywell UDC3300 Manual Page 54 Operation 46 UDC3300 Basic Model: DC330B User Manual 5/00.7 Alarm Setpoints manual Procedure for Displaying the Alarm Setpoints Table 4-9 Procedure for Displaying or Changing the Alarm Setpoints Step Operation.Both Normally Open and Normally Closed contacts are brought out to the rear terminals.Up to four setpoints are independently set as high or low alarm, two for each relay.Page 8 Specifications, continued Design (continued) Auxiliary Linear Output (Optional) (Isolated) 21 mA dc maximum into a negative or positive grounded load or non-grounded load of 0 to 1000 ohms.The instrument is capable of meeting these test levels with no component failures, no reset, and no incorrect outputs.Page 12 Installation 4 UDC3300 Basic Model: DC330B User Manual 5/00 Mounting Method Before mounting the controller, refer to the nameplate on the inside of the case andmake a note of the model numb.
Specification, overview, new Power and Flexibility, the UDC 3300 Universal Digital.
Page 57 Honeywell UDC3300 Manual Page 57 Operation 5/00 UDC3300 Basic Model: DC330B User Manual 49 DIG IN1 or DIG IN2 Selections Display Indication Action on Contact Closure Returns (toggles) to original state udc 3300 user manual when contact opens.